Welcome to the support page for
Here you will find all of the information that you require to get the most out of your Distributor 3.
If you cannot find what you are looking for then please use the search facility above.
The Distributor 1 contains one Distributor module within its case, whereas the Distributor 3 contains three modules. These three internal modules are completely independent of each other within the case. The Distributor 3 simply offers a more elegant solution for installations which need three or more Distributor modules.
Its main application is to add audio and control connectivity to Meridian DSP loudspeakers and the systems in which they are used. Some Meridian loudspeakers have only one input and one output and these are in the form of Meridian “Speakerlink”, a proprietary interface. Other models have a few additional connections, but their use with non-Meridian equipment is still limited in functionality. The Distributor opens up the loudspeakers for many other uses with third-party equipment. The Distributor also has applications which involve no Meridian loudspeakers and, in fact, no Meridian equipment whatsoever.
Although not a pre-amplifier in the traditional sense of the term, the Distributor can carry out some of the functions of a pre-amplifier. It acts as an “input switch” for a pair of DSP loudspeakers and it accepts commands to control volume and source selection. However, these commands must be in the form of Meridian comms or RS232, rather than front-panel controls or infra-red reception.
When connected via Speakerlink to certain models of Meridian loudspeaker, the Distributor takes its power over this connection and does not need an external PSU. However, the following models cannot provide this power and an external PSU is required; DSP420, all non-SE versions of DSP5200, DSP7200 and DSP8000, all non-SE “HC” models of DSP5200 and DSP7200. A suitable PSU is available from Meridian through the authorised distribution network.
The RS232 commands used by Meridian DSP loudspeakers are used. These can be found on Meridian TechNote TN51. It can be useful to note that, although the Distributor receives RS232 commands, the unit does not act on these commands itself. Rather, the commands are sent out of the Speakerlink output to be acted on by the Meridian product “downstream” of the Distributor. Meridian comms is then used to send relevant commands, such as source selection, back along the Speakerlink connection to the Distributor.
When the analogue input is selected, the Distributor uses high-quality A to D circuitry to convert analogue audio on this input into a digital audio signal running at 96kHz with 24 bit precision. This digital audio is switched through to the “Digital aux” and the Speakerlink output sockets.
When the digital input is selected, digital audio present on the input is switched through to the Digital Aux and Speakerlink outputs.
You may not need to. Although the inputs can be assigned to any of the twelve sources available on a Meridian system, by default they are already assigned to three of those sources. If the default arrangement is not appropriate, the Distributor can be configured as described on Meridian TechNote TN50.
The factory settings are CD = Digital input, Radio = Analogue input, Aux (SLS) = Speakerlink input. The RS232 commands for these are CD, RD and AX respectively. Further configuration details can be found on Meridian TechNote TN50.
Yes. By default, when a DSW is added to such a system the left and right loudspeakers receive a bass-limited signal. Their bass is crossed-over to the subwoofer. In some applications, this will achieve the desired effect. However, if the aim is to add bass on top of that produced by the left and right loudspeakers, the loudspeakers need to be set as full-range. This is done by sending each loudspeaker the relevant RS232 command. This can be done using a Serial-to-Speakerlink lead or by using the Distributor as a Serial-to Speakerlink converter. Next, if the system features a Meridian Audio Core product, its subwoofer controls can be used to tune the overall sound by adjusting the gain and the filter used by the DSW. However, if no Audio Core is present, the Distributor can be used to allow the sound to be tuned to suit while playing music. This is done by adjusting the gain and filter settings for the DSW via RS232 commands sent from a PC.