Welcome to the support page for
DSP3200 Digital Active Loudspeaker
Here you will find all of the information that you require to get the most out of your DSP3200 Digital Active Loudspeakers.
If you cannot find what you are looking for then please use the search facility above.
Floorstanding & Bookshelf Loudspeaker Firmware Update
With power applied to the product and the mains switch in the “On” position, the green LED on back-panel should illuminate
dimly. If it does not light up, the mains supply and the mains inlet fuse should be checked.
The DSP3200 comes out of Standby mode when it receives an appropriate communication signal from another Meridian product. This signal is received on the Speakerlink input socket of the loudspeaker and is produced when the rest of the system is brought out of Standby. When this happens, the green LED on the back-panel of the DSP3200 is illuminated brightly.
In Standby mode, the green LED on back-panel illuminates dimly. When out of Standby, the green LED illuminates brightly. As “brightly” and “dimly” are relative terms, it can be useful to watch the LED as the system is brought out of Standby. The change from dim to bright is quite obvious and should confirm whether the product is coming out of Standby mode.
Each loudspeaker uses a maximum of 200W.
The loudspeaker on the left (when viewed from the listening position) should be set to “L/C” and the loudspeaker on the right should be set to “R”. The switch is required because the Speakerlink lead feeding the loudspeaker carries both left and right audio channels. The switch “tells” the loudspeaker which channel to pick up from the lead. This is true even when each loudspeaker is fed with a dedicated Speakerlink lead.
Loudspeakers in use as main-left, side-left, rear-left or centre channels should be set as “L/C”. Set the switch to “R” for loudspeakers in use as main-right, side-right or rear-right channels.
Yes. If cabling arrangements or other physical considerations preclude star-wiring, daisy-chaining can be used for a pair of DSP3200. This applies as long as the two loudspeakers are a “pair” as defined in a Meridian system, i.e. they are the left and right main channels, the rear-left and rear-right channels or the side-left and side right channels.
As the DSP3200s are quite small physically, the general advice is to set them to “Small”. This will divert low-bass (as defined by the crossover setting in configuration) away from the loudspeakers in question and send it to the subwoofer and/or the “Large” loudspeakers in the system. The exact route of the bass is determined by several factors within configuration. However, in a system with no subwoofer, the main (front) loudspeakers are forced to be “Large”, regardless of their physical size. If all the other loudspeakers are defined as “Small”, the main loudspeakers will be asked to playback all the bass for the system. In such cases, defining DSP3200s as “Large” could help spread the bass load across the system. This could result in improved bass reproduction at low to mid volume levels and, as the DSP3200s feature bass-protection, even at high volumes the risk of “bottoming out” a bass drive is minimal.
Bass output can be increased, but it may require some configuration. Refer to our support documentation relating to DSW for further information.
This can be done if a Meridian 218 Zone Controller is also added to the system. The 218 has on-board DSP which can derive dedicated feeds for the subwoofer as well as the main left and right channels. The 218 features gain and filter controls to allow the subwoofer to be sonically integrated with the main loudspeakers.
There are three threaded inserts built into the underside of the DSP3200 cabinet for mounting the loudspeaker to its stand. However, there have been two differing dimensions used for the spacing of these inserts. The depth of the inserts also differs between these two variants. The standard DSP3200 loudspeaker stand pack includes a top plate which has its mounting holes spaced to suit one of the variants, but it doesn’t line up correctly with the other. To deal with this, an alternative top plate kit is available to suit the other design. This kit includes mounting screws to suit the different depth of the threaded inserts. The alternative plate kit can be ordered along with DSP3200 stands. It carries the Meridian stock code PA10655.
Yes, the loudspeakers feature four mounting holes on their back-panels which are spaced correctly to accept the “König and Meyer 24471” wall bracket.
Meridian Product Range Insight