Welcome to the support page for
DSP3300 Digital Active Loudspeaker
Here you will find all of the information that you require to get the most out of your DSP3300 Digital Active Loudspeakers.
If you cannot find what you are looking for then please use the search facility below.
Floorstanding & Bookshelf Loudspeaker Firmware Update
With power applied to the product and the mains switch in the “On” position, the green LED on back-panel should illuminate dimly. If it does not light up, the mains supply and the mains inlet fuse should be checked.
The DSP3300 comes out of Standby mode when it receives an appropriate communication signal from another Meridian product. This signal is received on the Speakerlink input socket of the loudspeaker and is produced when the rest of the system is brought out of Standby. When this happens, the green LED on the back-panel of the DSP3300 is illuminated brightly.
In Standby mode, the green LED on back-panel illuminates dimly. When out of Standby, the green LED illuminates brightly. As “brightly” and “dimly” are relative terms, it can be useful to watch the LED as the system is brought out of Standby. The change from dim to bright is quite obvious and should confirm whether the product is coming out of Standby mode.
Each loudspeaker uses a maximum of 550W.
The loudspeaker on the left (when viewed from the listening position) should be set to “L/C” and the loudspeaker on the right should be set to “R”. The switch is required because the Speakerlink lead feeding the loudspeaker carries both left and right audio channels. The switch “tells” the loudspeaker which channel to pick up from the lead. This is true even when each loudspeaker is fed with a dedicated Speakerlink lead.
Yes. If cabling arrangements or other physical considerations preclude star-wiring, daisy-chaining can be used for a pair of DSP3300s. This applies as long as the two loudspeakers are a “pair” as defined in a Meridian system, i.e. they are the left and right main channels, the rear-left and rear-right channels or the side-left and side right channels.
Loudspeakers in use as main-left, side-left, rear-left or centre channels should be set as “L/C”. Set the switch to “R” for loudspeakers in use as main-right, side-right or rear-right channels.
If the DSP3300s are amongst the smaller loudspeakers in the system, the general advice is to set them to “Small”. This will divert low-bass (as defined by the crossover setting in configuration) away from the loudspeakers in question and send it to the subwoofer and/or the “Large” loudspeakers in the system. The exact route of the bass is determined by several factors within configuration. However, in a system with no subwoofer, the main (front) loudspeakers are forced to be “Large”, regardless of their physical size. If all the other loudspeakers are defined as “Small”, the main loudspeakers will be asked to playback all the bass for the system. In such cases, defining DSP3300s as “Large” could help spread the bass load across the system. This could result in improved bass reproduction at low to mid volume levels and, as the DSP3300s feature bass-protection, even at high volumes the risk of “bottoming out” a bass drive is minimal.
Bass output can be increased, but it may require some configuration. Refer to our support documentation relating to DSW for further information.
No. Most subwoofers require to be fed with a variable analogue audio signal. This does not exist in a two-channel Meridian system. Even subwoofers which feature a digital input are unlikely to offer any practicable method of integration due to issues with controlling volume evenly across the system.
Yes. The DSP3300 is designed to work well in either “horizontal” or “vertical” orientations. This provides flexibility in use as a rear or side channel loudspeaker. However, as the DSP3300 provides extended bass which may not be associated with its cabinet size, it can make a great loudspeaker for use as a main left or right channel loudspeaker. To maintain appropriate appearance, the “Meridian” badge on the front of the loudspeaker can be rotated to suit the orientation.
This can be used under the loudspeaker to allow it to stand on one end in a vertical position or it can be under the loudspeaker in the horizontal orientation to angle the front of the loudspeaker slightly up or down towards the listening position.
Meridian Product Range Insight